Hexarmor Work Gloves & More: What I've Learned as a Buyer (And What I Wish I Knew)

Hexarmor Work Gloves & More: What I've Learned as a Buyer

When I first started managing PPE purchasing for our team, I assumed the most expensive glove was always the safest. That was pretty naive. After a few years and a couple of expensive mistakes, I've learned that 'best' depends on the job, the fit, and the supplier. Here's a FAQ covering the questions I get asked most often—and a few I wish I'd asked myself.

What exactly makes Hexarmor work gloves different?

I'm not a materials scientist, but I've seen the difference firsthand. Hexarmor's core thing is superior cut and puncture resistance. Their HexBlue and SharpsMaster technologies use a mix of high-performance yarns and special coatings—not just thick leather. For our guys handling sharp metal and glass, that's a game-changer. Most standard gloves get cut through; these give you a real chance to avoid injury. As of early 2025, their cut levels are consistently rated at ANSI A5 or A6, which is the top tier. Don't take my word alone—check their specs against your specific hazards.

Is the Hexarmor store the only place to buy? I've seen other prices.

You can buy direct from the Hexarmor store, but you'll also find authorized distributors online. I've used both. The official store is straightforward, especially for bulk orders. But I've found that some distributors offer slightly better pricing on specific models. However—and I learned this the hard way—always verify the seller. I once ordered from a third-party site because it was $50 cheaper on a case of gloves. They arrived with no packaging and didn't fit our size chart. Turns out they were factory seconds? Or maybe knockoffs. Now I either buy from the official store or from a distributor I've used before. That initial savings cost me in returns and trust.

How do Hexarmor gloves compare to other brands like Milwaukee or Studson?

This is the question I get most often. I'm not going to trash any competitor—Milwaukee makes good tools, and Studson has its place. But for pure cut and puncture resistance? Hexarmor is in a different league. I've tested both. For general construction, a cheaper glove is fine. But when you're dealing with sharp steel or glass, the performance gap is huge. I've had guys tell me their Hexarmor gloves survived scrapes that would have shredded their old pairs. It's about matching the glove to the risk. If the risk is low, don't over-buy. If it's high, don't cheap out.

What about Hawx work boots or Vans work boots? Are those worth looking at?

Look, I manage PPE, but boots are a different beast. I've heard guys swear by Hawx for comfort, and Vans have that casual work style. But I'm not a boot expert. What I've learned is that 'work boot' is a broad category, and your guys' needs vary. I focus on safety standards for boots like ASTM F2413 for impact and compression. Hexarmor doesn't make boots, which is sort of a relief—I don't need to pretend I'm an expert. If you're asking about those brands, check your company's safety requirements first. I can tell you that proper boots are just as important as gloves, but I'll point you to a specialist for that advice.

What is a tactical vest, and does Hexarmor make one?

Good question. A tactical vest is a type of body armor designed for military, law enforcement, or security use—often carrying plates and gear. No, Hexarmor does not make tactical vests. They focus on hand, head, eye, and face protection. I've learned that it's smart to know what a company is not good at. If a vendor tries to sell you everything, that's a red flag. Hexarmor's honesty about their focus actually makes me trust them more for what they do make. Same for tactical vests—I'd go to a specialist like Point Blank or Safariland for those.

How do I choose the right Hexarmor glove for my team?

This is the real challenge. Start with the hazard analysis. What are your workers cutting or handling? Hexarmor has a good online tool, but I also recommend ordering sample pairs. We ordered a few different models last year. Some guys loved the Helix series for dexterity; others needed the extra puncture protection of SharpsMaster. The biggest mistake I see is ordering one glove for everyone based on price. That never works. Budget for at least two or three different options depending on the job role. And measure hands! I can't tell you how many times people order 'large' because they think they have big hands, but they really need medium for a proper fit.

Are Hexarmor products compliant with current standards? (ANSI or EN)?

Yes, as of my last check in late 2024, Hexarmor gloves are tested to ANSI/ISEA 105 and EN 388 standards. They publish their cut, puncture, and abrasion ratings. But standards can update, so always verify against the latest requirements for your industry. I keep a binder with all our product spec sheets and the relevant standard pages. It's saved us during safety audits. If a vendor can't provide clear compliance data, walk away.

Where can I find more info or buy? Is the Hexarmor store reliable for shipping?

The Hexarmor store (hexarmor.com) is straightforward. I've had good luck with their shipping times for standard orders. For bulk custom orders, I'd contact a sales rep directly. My advice: don't wait until your stock is empty. I ordered a rush once and paid extra for expedited shipping. Not a fun experience. As for other stores, check if they're an authorized distributor. A quick call to Hexarmor's customer service can confirm that.